;*************************************************************************** ;* Copyright (C) 1989-1993 by NCR Corporation. ;* ;* This file contains proprietary and confidential information. All ;* rights reserved except as may be permitted by prior written consent. ;*************************************************************************** AdapterId 01BBh AdapterName "NCR 3360 SCSI SubSystem" NumBytes 4 FixedResources pos[0]=XX1XXXXXb pos[1]=XXX0XXX0b pos[3]=110XXX1Xb NamedItem Prompt "Board Enable" choice "Enabled" pos[0]=XXXXXXX1b choice "Disabled" pos[0]=XXXXXXX0b Help "This option will allow you to disable this SCSI board in the system. Once this board is disabled, no SCSI devices on this board can be accessed after the next system boot. The default condition is SCSI board enabled." NamedItem Prompt "Host Adapter Board Interrupt Level" choice "INT LEVEL 14" pos[0]=11XXXXXXb int 14 choice "INT LEVEL 11" pos[0]=10XXXXXXb int 11 choice "INT LEVEL 5" pos[0]=01XXXXXXb int 5 choice "INT LEVEL 3" pos[0]=00XXXXXXb int 3 Help "Set the Host Adapter Board Interrupt Level so it will not conflict with other interrupting devices." NamedItem Prompt "Arbitration Level" choice "DMA Level 14" pos[0]=XXX1110Xb arb 14 choice "DMA Level 13" pos[0]=XXX1101Xb arb 13 choice "DMA Level 12" pos[0]=XXX1100Xb arb 12 choice "DMA Level 11" pos[0]=XXX1011Xb arb 11 choice "DMA Level 10" pos[0]=XXX1010Xb arb 10 choice "DMA Level 9" pos[0]=XXX1001Xb arb 9 choice "DMA Level 8" pos[0]=XXX1000Xb arb 8 choice "DMA Level 7" pos[0]=XXX0111Xb arb 7 choice "DMA Level 6" pos[0]=XXX0110Xb arb 6 choice "DMA Level 5" pos[0]=XXX0101Xb arb 5 choice "DMA Level 4" pos[0]=XXX0100Xb arb 4 choice "DMA Level 3" pos[0]=XXX0011Xb arb 3 choice "DMA Level 0" pos[0]=XXX0000Xb arb 0 choice "DMA Level 1" pos[0]=XXX0001Xb arb 1 choice "DMA Level 2" pos[0]=XXX0010Xb arb 2 Help "The NCR SCSI Adapter supports the direct memory access (DMA) mode of data transfer. Each DMA level has a corresponding priority level; the lower the DMA level, the higher the corresponding priority. You may select any one of the DMA levels listed. We recommend you select the first level listed, DMA level 3. If your selection conflicts with a DMA level already assigned in the system, it will be marked with an asterisk and you must select an alternative level." NamedItem Prompt "On-Board RAM Starting Address" choice "D0000h-D1FFFh" pos[1]=100XXXXXb mem 0D0000h-0D1FFFh choice "D4000h-D5FFFh" pos[1]=101XXXXXb mem 0D4000h-0D5FFFh choice "D8000h-D9FFFh" pos[1]=110XXXXXb mem 0D8000h-0D9FFFh choice "DC000h-DDFFFh" pos[1]=111XXXXXb mem 0DC000h-0DDFFFh choice "C0000h-C1FFFh" pos[1]=000XXXXXb mem 0C0000h-0C1FFFh choice "C4000h-C5FFFh" pos[1]=001XXXXXb mem 0C4000h-0C5FFFh choice "C8000h-C9FFFh" pos[1]=010XXXXXb mem 0C8000h-0C9FFFh choice "CC000h-CDFFFh" pos[1]=011XXXXXb mem 0CC000h-0CDFFFh Help "Set the On-Board RAM Starting Address to avoid conflict with other adapters which use the channel memory area (segments C000 and D000) for ROM or RAM. The default is D0000h." NamedItem Prompt "SCSI Channel A Host Logical ID" choice "7" pos[1]=XXXX111Xb choice "6" pos[1]=XXXX110Xb choice "5" pos[1]=XXXX101Xb choice "4" pos[1]=XXXX100Xb choice "3" pos[1]=XXXX011Xb choice "2" pos[1]=XXXX010Xb choice "1" pos[1]=XXXX001Xb choice "0" pos[1]=XXXX000Xb Help "Set the Host Adapter Board Logical ID to avoid conflict when performing adapter to adapter I/O. The default is 7." NamedItem Prompt "SCSI Channel B Host Logical ID" choice "7" pos[3]=XXX111XXb choice "6" pos[3]=XXX110XXb choice "5" pos[3]=XXX101XXb choice "4" pos[3]=XXX100XXb choice "3" pos[3]=XXX011XXb choice "2" pos[3]=XXX010XXb choice "1" pos[3]=XXX001XXb choice "0" pos[3]=XXX000XXb Help "Set the Host Adapter Board Logical ID to avoid conflict when performing adapter to adapter I/O. The default is 7. This option is only active if there is a Daughter Card attached." NamedItem Prompt "I/O Address Select" choice "0800h" pos[2]=000010XXb io 00800h-008FFh choice "0C00h" pos[2]=000011XXb io 00C00h-00CFFh choice "1000h" pos[2]=000100XXb io 01000h-010FFh choice "1400h" pos[2]=000101XXb io 01400h-014FFh choice "1800h" pos[2]=000110XXb io 01800h-018FFh choice "1C00h" pos[2]=000111XXb io 01C00h-01CFFh choice "2000h" pos[2]=001000XXb io 02000h-020FFh choice "2400h" pos[2]=001001XXb io 02400h-024FFh choice "2800h" pos[2]=001010XXb io 02800h-028FFh choice "2C00h" pos[2]=001011XXb io 02C00h-02CFFh choice "3000h" pos[2]=001100XXb io 03000h-030FFh choice "3400h" pos[2]=001101XXb io 03400h-034FFh choice "3800h" pos[2]=001110XXb io 03800h-038FFh choice "3C00h" pos[2]=001111XXb io 03C00h-03CFFh choice "4000h" pos[2]=010000XXb io 04000h-040FFh choice "4400h" pos[2]=010001XXb io 04400h-044FFh choice "4800h" pos[2]=010010XXb io 04800h-048FFh choice "4C00h" pos[2]=010011XXb io 04C00h-04CFFh choice "5000h" pos[2]=010100XXb io 05000h-050FFh Help "You may set the NCR SCSI adapter to any one of the I/O Addresses listed. The first choice is recommended. If your selection conflicts with an I/O address already assigned in your system, it will be marked with an asterisk and you must select an alternate address." NamedItem Prompt "SIOP Fairness/Priority" choice "Fairness Enabled" pos[2]=XXXXXXX1b choice "SIOP A Priority" pos[2]=XXXXXX10b choice "SIOP B Priority" pos[2]=XXXXXX00b Help "If 'Fairness' is enabled, the SIOPs on each SCSI Channel will take turns accessing the MicroChannel Bus. If SIOP A or SIOP B have priority, that SIOP will always win the MicroChannel Bus when the two SIOPs compete." NamedItem Prompt "MicroChannel Fairness" choice "Enabled" pos[3]=XXXXXXX0b choice "Disabled" pos[3]=XXXXXXX1b Help "If 'Fairness' is enabled, the NCR SCSI Adapter will not compete for the channel during the next arbitration phase if it is currently in control of the channel. This allows other installed adapters to obtain the channel in the next sequence based on each adapter's assigned priority level. When 'Fairness' is disabled, the adapter will compete for every arbitration phase and will obtain more than its fair share of channel usage. We recommend you use 'Fairness Enabled' for all adapters."