IBM eServer BladeCenter HS40 Firmware Flash Disk Version 1.18, Build ID: BRMK18A Installation README File System Supported: 8839 CONTENTS ________ 1.0 Overview 2.0 Change History 3.0 Installation and Setup Instructions 4.0 Configuration Information 5.0 Web Sites and Support Phone Number 6.0 Trademarks and Notices 7.0 Disclaimer 1.0 Overview 1.1 This README file contains the latest information about installing the IBM eServer BladeCenter HS40 Firmware. 1.2 Limitations - NA 1.3 Enhancements - NA 1.4 Level of Recommendations and Prerequisites for the Update: - This update is recommended. 1.5 Dependencies 2.0 Change History Version 1.17 - March 19, 2004 ---------------------- - Initial release Version 1.18 - April 30, 2004 ---------------------- - Fixes for sensor monitoring on BSE daughter card 3.0 Installation and Setup Instructions *Note: If installing from an update package, see additional instructions, in Appendix A. The procedure to update the BMC is as follows: 3.1 Boot to or insert the BMC firmware update diskette into drive 3.2 Recommended user copy LCREFLSH.BAT, FWPIAUPD.EXE, FRUSDR.EXE, BRMK18A.HEX and *.SDR file from BMC firmware diskette onto hard drive (optional, but highly recommended as flash times are considerably longer executing from floppy) 3.3 Type LCREFLSH.BAT. Hit 'Enter' Note: If there are problems, check the boot block jumper (J5G1). Must be on pins 1 & 2 3.10 Instructions for updating BMC if operational code becomes corrupted 3.11 Remove HS40 blade 3.11 Move switch BMC_Force_Update (S6H1, bit 5) to On. 3.12 If updating BMC boot code, ensure Write Protect jumper (J5G1) connects pins 1 & 2 3.13 Place HS40 blade in chassis. It will automatically power up and begin booting. Correct KVM and CD selection will automatically occur. 3.14 In DOS run FWPIAUPD 3.15 Remove HS40 blade 3.16 Move switch BMC_Force_Update back to Off 4.0 Configuration Information 5.0 Web Sites and Support Phone Number 5.1 IBM Support Web Site: http://www.pc.ibm.com/support 5.2 IBM Marketing Web Site: http://www.pc.ibm.com/ww/eserver/xseries/ 5.3 If you have any questions about this update, or problems applying the update go to the following Help Center World Telephone Numbers URL: http://www.pc.ibm.com/qtechinfo/YAST-3P2QLY.html. 6.0 Trademarks and Notices 6.1 IBM and the e(logo) are registered trademarks of International Business Machines Corporation. 6.2 U.S. Government Users Restricted Rights - Use, duplication or disclosure restricted by GSA ADP Schedule Contract with IBM Corporation. IBM web site pages may contain other proprietary notices and copyright information which should be observed. 7.0 Disclaimer THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES TO ANY PATENTS OR COPYRIGHTS.  Appendix A: Package Specific Installation Instruction This update is packaged as a self-extracting PackageForTheWeb (PFTW) executable file. To unpack, this update requires that your TEMP environment variable be set to a path with read/write access. You must be logged in as an administrator. The package update log, ux.log, is created on the system drive. To locate the log file go to: %SystemDrive%\uxlog\ux.log The command-line syntax for PackageForTheWeb firmware update package is: Package.exe [-s] [-a [-s] | [-r] | [-c] | [-x directory] | [-xd] | [-w] | [-?] ] [-s] This command installs the Package-For-The-Web software silently and does not prompt if files are to be over-written in the %temp% directory. [-a] This command passes all subsequent commands to the PFTW software to install the update package. [-s] This command runs a silent and unattended update. For firmware updates, the update is scheduled to run on the next reboot. An immediate reboot can be forced with the -r option. [-r] This command schedules the update and reboot immediately. It can be used with or without the -s command. [-c] This command cancels any scheduled firmware update and records results of this operation in the log file. Only one firmware package can be scheduled at a time, if a firmware update needs to be applied instead of the currently scheduled firmware update package, cancel the current (run with the -c option on any firmware package) package. Then, run the applicable firmware package. [-x directory] This command is used with firmware updates to extract the update to the directory named directory. The PackageForTheWeb executable extracts itself to a subdirectory in the %TEMP% directory, a relative directory will be relative to that location. You must specify an absolute directory if you do not want to use the default directory. [-xd] This command is used with firmware updates to extract to a floppy diskette. The floppy diskette can then be used to boot from and apply the update. This option is not available for all firmware updates, such as tape drive and hard-disk drive updates. [-w] PowerQuest Virtual Boot Environment requires that there are 2 free sectors on the first track before it can schedule a firmware update. Use this option only if scheduling an update failed because 2 free sectors were not available on the first track. This option clears the non-boot and the non-partition information sectors on the first track. Typically, these sectors are not used. Before clearing the sectors a copy of the complete first track is saved in the %temp% directory from which the update runs. [-?] This command displays information about the command line switches. The command line switches -s, -r -c and -e are unnattended. Other command line options such as display help (-?) might require that you hit any key to continue. If Windows packages are run without any command line options, a GUI is displayed. This GUI offers all of the options that are available using the command line.