LSI Dos HyperCFG Ver 3.6 CONTENTS --------- 1.0 Overview 2.0 Fixes 3.0 Features 4.0 Web Sites and Support Phone Number 5.0 Disclaimer 1.0 Overview -------------- 1.1 Overview about this code HYPERCFG is a DOS command line utility for LSI IDE RAID. 2.0 Fixes -------------------- - /EA/EE/EC options were erasing configuration/error-log from primary master only, if no channel and drive are specified. - /T, /Ti options were removed. - Hypercfg utility was causing RDM to lose Ethernet connectivity 3.0 Features ----------------------------------------- Component Features /S - Silent Operation: When this option is set, the utility does not prompt the user. /F[FILENAME]: This Option redirects the output to the specified FILENAME If FILENAME is not specified then the default file is taken to be HYPERCFG.DAT. /Yx[filename] This option is used for error logging If filename is not specified the default is hypercfg.log 'x' = f - default - log only errors. 'x' = c - continuous logging CONFIGURATION OPTIONS: The options specified with '[]' are optional and those within '<>' are mandatory. These options are used to configure the RAID. The valid switches are: /A[m]:D1[,D2,D3,D4] /G[N]:[SIZE1] /G[N1]:[SIZE2]- Automatic RAID configuration m = S[STRIPE SIZE] - configures RAID in STRIPE MODE(RAID-0) with specified STRIPE SIZE. STRIPE SIZE must lie within the range [32, 64, 128, 256, 512, 1024, 2048, 4096]. If invalid STRIPE SIZE is specified the utility assumes 64K STRIPE SIZE. Default STRIPE SIZE is 64k m = M - configures RAID in MIRROR MODE (RAID-1) m = R[STRIPE SIZE] - configures RAID in RAID 10 mode with specified STRIPE SIZE. STRIPE SIZE must lie within the range [64...4096], in multiples of 4K. D1, D2...D4 specifies the drive that participates in the array. Valid nos. are 00,, 10, for Port#0, Port#1 respectively. /G[n]:[size] creates a logical array in the array 'n' with the size specified Size specified is in MB Default value for n is 0 and if size is not specified, the whole array is allotted to the logical drive. DRIVE-ID: Drive id is specified by /C[n] /D[cd] /C[n] - Specifies the card no. If n is not specified, then it is taken to be 0 /D[cd] - Specifies the drive no. c = Channel No. (0 - for Primary, 1- for Secondary) - default is 0 d - Always 0 for this controller, only Master is supported. /L /C[n] /D[cd] [/b[filename]]- Displays the configuration sector of the specified drive - If ONLY /L is used, the configuration sector of the first available drive is displayed. The order of searching for the first available drive is: Card 0 Channel 0 Drive 0 - Primary Master Card 0 Channel 1 Drive 0 - Secondary Master . . . - If either /D or /C is specified then the configuration sector of the specified drive is displayed - /b[fn] - saves the IRCD in a bin file - fn. If fn is not specified, default is HYPERCFG.BIN /E /C[n] /D[cd] - Erases the configuration/error log sector of specified drive o = C - Erases the configuration sector o = E - Erases the error log sector o = A - Erases both configuration and error log sector /@ /b[filename] To restore configuration from binary file use /@ /b[binfile] If binfile is not specified, then default is HYPERCFG.BIN DISPLAY OPTIONS: This option determines how the data is displayed. This option is valid only for /I option. /W[o] - Specifies display mode o = V - Display in verbose mode Default Option: If [o] is not specified, then display will be as HEX Dump. MISCELLANEOUS OPTIONS: /M[r/] /C[n] /D[cd] (NOTE: This feature is available only in DOS version) This option allows the user to set the maximum accessible sectors on the Harddrive that supports this feature. The address is specified in HEX /Mr - Resets the max. address to NATIVE MAX ADDRESS of HDD. /P[S] /C[n] /D[cd] - Switches the drive to specified state. S = S - Drive is powered on in Suspend state. Default Option: If [S] is not specified, then the drive is switched on in Active state. /V - Detects the Presence of RAID BIOS and displays the version of BIOS (NOTE: Feature availability depends on driver used for non-DOS platforms) /R[n] [/$[FILENAME]] [/B[FILENAME]] /C[n] /D[cd] - Reads and displays the 'n'th sector If 'n' is not specified then sector no. is taken to be 0 /B option dumps specified sector to the specified file in BIN format /$ option dumps specified BIN file to the 'n'th sector The default filename is HYPERCFG.BIN /X - This option pauses and waits for keystroke if any error occurs on executing HyperCFG. /I[a] /C[n] /D[cd] [/B[filename]] - Displays the information about the specified drive /Ia displays ID Device Packet for all drives present. /Bfilename - Saves the 512 byte ID info. Pkt. To filename. If filename is not specified, then the default filename is HYPERCFG.BIN This option should NOT be used with /Ia option. /Z[E/D] - Enables / Disables SMART feature. Default option is ENABLE Note: DMA and Write cache are made ON by default while creating R0/R1/R10 4.0 WEB Sites and Support Phone Number ---------------- 4.1 IBM Support Web Site: http://www.pc.ibm.com/support 4.2 IBM Marketing eserver Web Site: http://www.ibm.com/eserver/xseries 4.3 If you have any questions about this update, or problems applying the update go to the following Help Center World Telephone Numbers URL: 800-IBM-SERV (800-426-7378) Hardware Support #: 800-426-4378 Software Support #: 800-237-5511 4.4 Website for the World Wide Support Phone list: http://www.pc.ibm.com/qtechinfo/YAST-3P2QYL.html. 4.5 IntelliStation web site: www.pc.ibm.com/intellistation 5.0 Disclaimer ---------------------------- 5.1 THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES TO ANY PATENTS OR COPYRIGHTS. 5.2 Note to Government Users Include the following note after the disclaimer paragraph. Note to U.S. Government Users -- Documentation related to restricted rights -- Use, duplication or disclosure is subject to restrictions set forth in GSA ADP Schedule Contract with IBM Corporation.