IBM eServer xSeries 225 (8649) Flash Update 
               Version 1.05 - Build OQE105A
                 Installation README File



CONTENTS
________

       1.0   Overview
       2.0   Change History
       3.0   Installation and Setup Instructions
       4.0   Configuration Information
       5.0   Unattended Mode
       6.0   Web Sites and Support Phone Number
       7.0   Trademarks and Notices
       8.0   Disclaimer

       1.0   Overview

              1.1  This README file contains the latest information about installing
                   the IBM xSeries x225 (8649) POST/BIOS code.

              1.2  Limitations - NA

              1.3  Enhancements - NA

              1.4  Level of Recommendations and Prerequisites for the Update:

              1.5  Dependencies

        2.0   Change History

              BIOS Version 1.05 - Build OQE105A
                 - RSA II"DHCP Control Enable" report issued
                 - corrected set POP password,reboot and enter system event error log page
                 - can now mount USB CDROM and FDD at same time 
                 - removed erroneously issued "Bad EEprom CRC error" messages 
                 - fan speed control reduced below 800rpm per spec.
                 - fan5 error issued when unplugging fan3 and fan4 with RSA II card, this was corrected


              BIOS Version 1.04 - Build OQE104A
                 - Initial release


        3.0   Installation and Setup Instructions

              The procedure to update the POST/BIOS is as follows:

              3.1  Insert the "IBM xSeries x225 (8649) POST/BIOS
                   Flash Diskette" into drive A.

              3.2  Start up or restart your IBM system.

              3.3  The system will boot off of the diskette.

              3.4  You will then be asked if you would like to save the current
                   code to a diskette.  If you select 'Y', you need to name
                   the file to be saved. The file will be saved on the diskette.
                   If you select 'N', the utility will continue to the next step.

              3.5  At this point, you will be asked if you would like to continue the
                   POST/BIOS flash update. If you select 'Y', the system will update
                   the flash ROM with the new code.  When this is complete you will be
                   prompted to remove the diskette and hit 'F1' to reboot the system.
	
	      3.6  On the first system boot, after updating the BIOS, select the Setup Utility 
		   with the F1 key; then, select the "Load Default Settings" option.
		   Select the "Save Settings" option, and hit 'y' to save.  Then, select
                   "Exit Setup" to exit the utility, and, finally, accept the displayed
                   'Y' option under "Save and exit the setup utility?"  


       4.0  Configuration Information

       5.0  Unattended Mode

             5.1   Steps for unattended mode.

                    5.1.1  Modify AUTOEXEC.BAT on the Flash Diskette to read:
                          "AF.EXE flashfil.fls /py /sn", where 
                          'flashfil.fls' is the file you wish to flash
                    5.1.2  Reboot the system with the Flash Diskette in Drive A:


       6.0  Web Sites and Support Phone Number

              6.1   IBM Support Web Site:
                     http://www.pc.ibm.com/support

              6.2   IBM Marketing IntelliStation Web Site:
                     http://www.pc.ibm.com/intellistation

              6.3   If you have any questions about this update, or problems
                    applying the update go to the following Help Center World
                    Telephone Numbers URL:
                     http://www.ibm.com/planetwide/.


       7.0  Trademarks and Notices

             THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
             KIND. IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR
             IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED
             WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND
             MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS
             DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES
             TO ANY PATENTS OR COPYRIGHTS.


       8.0  Disclaimer